Jaguar Forum banner
1 - 8 of 112 Posts

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
How did you get round this in the end, rename files?
 

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
It'd be good to ask him and post here as I'm sure it'd help others a lot
 

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
And how difficult is the change of the ABS unit?
If i want to retrofit ACC first i have to change my ABS ;(
looking at it, I don't think it's difficult at all......but I haven't done it :D
You do like to add options don't you ? (y)
 

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
Good luck with finding a -B variant. Damn near impossible to find.

Yes, that's the cable/connection needed.
Like hens teeth apparently, Oh I thought that connector was for the pollution sensor?
 

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
@Gav you mean to say I should check it at the bottom of the grille? I don't want to start buying stuff if the car doesn't have a cable loom run already because that would not be possible for me to do. If the connection is already there then it's worth looking around for parts.

Many thanks once again

Kind regards
Jay
Jay sorry not sure, but I had the pollution sensor on my last xf and I鈥檝e a feeling the connector was there.
Might have changed on the x260 so do your homework.
 

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
Does MoJo's answer not help Jay?
It does mate, but like I say on my x250 I thought that was used for the pollution sensor which I had. But easy peasy I could be wrong as this is an x260
 
  • Like
Reactions: PeteA

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
Good luck Tommy, hope it all goes smoothly
 
  • Like
Reactions: PeteA and Statler

Registered
馃彺鬆仹鬆仮鬆伋鬆仯鬆伌鬆伩X260 R-Sport in Aurora Red
Joined
14,315 Posts
One short question for my Timeplan...
How long does it take to change the abs module?
I have support from 2 mechanics and their tools.

2 hours? Or longer?
Not done it myself but I would have thought 2 hours will be enough.
as your changing the brake fluid I鈥檇 suggest using SDD to drain all fluid out (standard DOT 4) so that when you take the abs module off there鈥榮 less chance of spilling brake fluid onto your paintwork, but have plenty of water /rags handy in case you do so you can immediately wash off. As for capacity imagine I can鈥檛 imagine it鈥檒l be more than 2L but the capacity should be online in jaguar manual.
 
1 - 8 of 112 Posts
Top